New plaster how many coats paint

With all the prep work done, you can now paint your wall and decorate your room as you would normally. Looking for more tips and tricks from Dr Dulux? Brush up on your paint finishes or find out how to paint tricky surfaces. Discover decorating trends and ideas in our new monthly newsletter.

By checking this box, you confirm that you have read and agree to our Terms and Conditions , and our Privacy Policy. If you'd like to know more about how we use your personal data, please read our privacy statement. Our latest tips and inspirations are on their way to your mailbox.

If you accepted all cookies, login with…. Password requirements: At least one capital letter At least one special character or number Minimum of 8 characters.

Show more Show less. Successfully registered, please login Login. Password changed successfully. Back to my account. Back to login. We will use this to provide you with useful information. In the next month. From months. After 6 months. Living room. Here are a few areas where you need to pay particular attention to avoid issues when painting your newly plastered walls. The first thing you need to do with newly plastered walls is to prevent the surface from being as absorbent so that when you apply the topcoat of plaster it then sticks properly.

A good solution, and one which is used frequently is to mix water and simple emulsion together and apply this to the surface of the freshly plastered wall before starting your paint-job properly.

This is commonly known as a mist coat. The purpose of applying this thin coat of emulsion-water mixture is to give the plaster the task of soaking up the water in the mixture. When soaking up this water the plaster then becomes far less absorbent and this lays the foundation for the proper base coat of paint. You can always add more water if the mixture is still too thick afterwards. You should also be sure that the paint you are using for the diluted mixture is a non-vinyl paint too.

You should also ensure that the watered-down paint is mixed from a light coloured paint too ideally white. Be careful when using the watered-down emulsion mixture for your mist-coat. It can be messy and there will be plenty of dripping as the water naturally thins out the paint. When using this mixture ensure you use plenty of dust-sheets and keep wiping down the roller and rubbing in any drip marks in the coating as you apply so that you do not end up with a less than professional finish which could ruin the whole job.

One problem you might find if you apply a white top coat of paint to new plaster is that it can take many different coats to cover the surface properly, and this could appear in patches too. If you are finding that you get some problem areas then a good stain block for paint or a good base-coat for emulsion can help a lot on these patchy areas. Applying a base coat or stain blocker will undoubtedly save you time and money if you are having a patchy wall problem.

The paint industry has long been aware there will be occasions where you have no option but to paint over walls which are not perfectly dry. There are specialist paints for new plaster which you can buy in good DIY stores.

Paint for new plaster is designed especially to cover plasterboard, brick, concrete and new plaster. At the same time this paint allows for the plaster to continue drying. The drying process continues afterpaint application because of the mixture of polymers in the solution. The polymer mixture allows the substrate to breathe properly and continue to dry even after the new paint has been applied to the fresh plaster. Specialist paints for new plaster will be more expensive than if you simply water down a cheaper emulsion, however, you will find they are usually much less messy as they do not have the 'drip-everywhere' problem of watered down emulsion.

Specialist paints for new plaster may also be available in only a limited number of colours compared with normal paint. These microporous paints are also often intended for external use rather than internal use. Choices may be limited. You need to understand the unusual properties of fresh plaster, any priming involved and more for a professional finish. You'll need to factor in just a little patience also For new work, like new plaster, dilution of the first coat known as the mist coat is essential, as this allows the paint to sink into the surface and bind to it.

Follow with two full, undiluted coats to finish. Start by opening doors and windows, and don't start painting until the plaster is bone dry. This could mean waiting a few days or even weeks for a room to dry. It is worth the wait though to do it right.

Follow these steps for perfect results every time. Plaster will suck up any moisture like a sponge, so the longer you leave it to dry, the easier it will be to achieve an even result. The time it takes for plaster to dry out will depend on the room's temperature, ventilation and the plaster's thickness.

As a general rule, wait four weeks per 5mm of plaster depth. Ensure that there are no dark patches on the freshly-plastered surface before you being to paint — a uniform, light, color is a good indicator as to whether your plaster has dried thoroughly. Newly built or altered rooms also take a while to settle, so waiting will mean you can fill any cracks that form as a result, before you paint.

Fresh plaster is extremely porous, and any moisture will be quickly absorbed into the wall. This is why you need to water down your first paint layer known as a mist coat. To make a mist coat, combine a cheaper emulsion paint in a similar color to your top coat with water. The ratios for this will vary according to the paint you are using, so check what it says on your paint tin — but around three parts paint to one part water should suffice. Stir the solution until you have an even consistency with no water sitting on top of the paint.